Garage door openers can last for years without needing to be replaced or fixed. This is especially true with the proper care. However, like every object that undergoes wear and tear on a daily basis, garage door openers will eventually need replacing. Luckily replacing your garage door opener can provide improved safety, efficiency, and noise levels. Wondering if it might be time to replace yours? Read on for 5 signs your garage door opener needs to be replaced!
This tends to be the most obvious sign that your garage door opener is malfunctioning. First, ensure the problem isn’t being caused by an object blocking the sensor or the door. Once you establish it isn’t an object, the problem either lies with the remote batteries or the track. Try replacing the batteries first. If the problem persists, then it’s time to call in the professionals!
If your garage door begins to reverse while it’s opening, or suddenly reverses after closing, it may be time to replace or repair your garage door opener. First check that there isn’t an issue with the sensor. If the sensors are aligned and nothing is blocking their path, then the garage door opener will need replacing.
If your garage door opener experiences intermittent and random functionality, it likely has an issue with the wiring. This random opening and closing creates a safety hazard, so be sure to get a professional’s opinion as soon as possible.
While a little bit of noise is to be expected, grinding, scraping, screeching, and rattling are signs of an issue. Get your opener inspected to avoid any problems or long term damage to the garage door.
Is your garage door stalling or, even worse, getting stuck? This could indicate a malfunctioning door opener. Get the door looked at as soon as you can by a qualified, trusted professional.
Overall, if your garage door is not opening smoothly and soundly in a timely manner, then there may be an underlying problem. Luckily, this malfunction gives you the opportunity to invest in a smarter and safer garage door opener. We hope these tips help! When in doubt, contact a professional at Info@adamsdoorsystems.com.
Why should you seal your garage door? On top of assisting with energy efficiency, gaps between your garage door and it’s surroundings can allow water, dust, and even pests into your home. This can cause damage to stored items, water build-up, and more. Luckily, sealing your garage door is a pretty simple process that involves replacing the bottom door seal and the weather-stripping along the sides and top of the door. If you are looking for an extremely airtight seal, you can even weather-strip between the individual door panels! Ready to learn the process? Keep reading.
The door sweep, also known as the bottom seal, is a long strip that attaches to the bottom edge of the garage door. The flexible material compresses when the door closes, effectively sealing the gap and keeping out weather, critters, and water. How do you know if it’s time to replace the bottom seal? You will be able to see daylight peaking through the cracks! Installing the rubber or vinyl seal is pretty easy. There is an aluminum channel on the bottom of the door that holds a U-Shaped Rubber Gasket. The gasket easily slides into two small tracks on the channel and voila! These gaskets can even be adapted to wooden garage doors for simple installation.
The Threshold Seal
The threshold seal is very similar to the bottom seal of a garage door. The only difference is the seal attaches to the floor rather than the door. Typically, thresholds are more durable than door seals and are installed with an adhesive that sticks to the ground. However, it is important to note that thresholds block water from exiting the garage just as much as they block water from entering, and make it a bit more difficult to sweep debris out.
The sides around the door are susceptible to wind and rain. To prevent this from occurring, a rubber or vinyl weather-stripping can be installed along the stop molding that is attached to the door jamb. Weather-stripping comes in rolls which are easily cut to the length you need, and further installed with galvanized nails or screws. Make sure the flange of the weather-stripping presses against the door for a good seal.
Looking for more DIY tips and knowledge? Contact our team at Info@adamsdoorsystems.com today!
You probably haven’t thought much about your garage door springs…until one breaks. You can call a professional, or try to replace the garage door yourself. Just know that this DIY project comes with hazards, especially if you are not that experienced with tasks like this. To help you tackle this problem, our team has compiled the following helpful tips. Read on to learn how to replace your garage door springs yourself!
Residential garage doors have one or two types of springs – torsion or extension. Heavy-duty torsion springs are mounted around a metal rod that runs parallel to the door. Extension springs are the long, lighter weight springs that run perpendicular to the door above the tracks. Be sure to purchase the right style spring, with the same length and diameter as the old springs.
We hope these tips help! When in doubt, contact a professional at Info@adamsdoorsystems.com!
(Source: Bob Vila)
Wondering if your garage door is working properly? As commercial and residential garage door professionals, we’ve seen it all! In this article we will go over the top 3 signs your garage door isn’t working properly, and what you can do about it.
If your garage door isn’t opening when you press the button from your car, it could be a sign that the transmitter has gone bad. To check if it is the batteries from your car’s transmitter, try pressing the button from the wall inside your garage. If the door still opens, you will need to replace the batteries in the car. Since most batteries are installed at the same time, you will likely need to change the batteries in the wall’s transmitter soon as well.
If you are experiencing this problem, it most likely means the photo eyes, which transmit a beam across the floor to prevent doors from closing on objects, may be dirty. This dirt will block the beams and prevent the garage door from closing. These photo eyes can also eventually become misaligned. To fix this problem, gently clean the photo eyes with a soft cloth and a mild, streak free cleaner. To test the alignment, measure the distance of the photo eyes from the ground up and use a level to make sure they are pointing directly across from one another.
If you are hearing a rubbing noise when your garage door opens at a certain point each time, it could indicate your tracks are misaligned. This is a serious issue, as the weight of the door can exacerbate the problem until it becomes a danger to operate the garage door. If the door is not moving at all, you should call in the professionals. Otherwise, you can realign the track by loosening the screws and gently tapping the track with a rubber mallet until it is back in position. This should be done to both tracks. Be sure to securely tighten the screws to ensure the track will not move any further.
Looking for more DIY tips and knowledge? Contact our team at Info@adamsdoorsystems.com today!